Yes, that's right - I did say jewelry. Nothing fancy, just simple and fun to wear! Again I have used papers from the Olivia paper packet. I can't help but be drawn over and over again to the rich autumn colors of these papers!!
Each pendant starts with an every day metal washer. I used some Liquid Glass and covered the front of the pendant with my paper of choice. Once it dries, simply trim around the paper. So easy! For a little more finished look you can leave 1/4" of paper and wrap it around to the back of the washer and stick it down with more liquid glass. Snipping the paper into the washer every 1/8" inch or so will allow it to wrap nicely without any crinkles.This first pendant I then sprayed with some shimmer mist. It doesn't show in the photo but it adds a real pretty sparkle!
After the paper is adhered to the washer and shimmer misted I then covered it entirely with a layer of Liquid Glass. This pendant I misted heavily with the shimmer mist. It dries in little pools this way, but I love the marbley look it made!
This last one I added some Opaques prior to the Liquid Glass. They could also be added when the LG is wet, but I wouldn't add them after it sets. Once the Liquid Glass has set completely (I usually give it over night before I start playing with them again) add a cord and any other accessories you may want. Fun to make, fun to wear! Let your imagination go wild with ideas!

Turn the pot upside down and glue the strips to the bottom with more Liquid Glass. I placed my pot over a jar to keep the paper from being squished around the top. An alternate way to 
With Liquid Glass, glue the ends of your
This is how your
Make a cone using a scrap of CS. My scrap was about 3" x 4". I used
Cut the large end of the cone to make an even opening.
Bend these short pieces outward like a sunburst.
Place the narrow end of the cone on the center back of the large B&T/CS circle. Place a pencil inside the cone and draw a circle on the CS using the narrow end as your template.
Remove the cone. Using an
Using Liquid Glass or the thicker Scotch glue, run a line around the edge and the inner edge of the large end of the cone.
Place the gluey edge on a scrap of CS and hold in place until secure. Allow to dry thoroughly.
Close the cuts of the smaller end of the cone and insert it into cut in the large B&T/CS circle from the B&T side. Open up the
Making the leaves and vines:
Cut two 12" x 1" strips from the green B&T. Cut out the leaves. Notice the pretty color on the back of the leaves. Again, this is what I love about
Now spray a leaf with the mister. Soggy is okay. Wrap a small portion of the leaf around a smooth slender object. I used my piercing tool. Any thing of this shape will work as long as it won't be damaged by heating. Using a heat embossing tool, heat the leaf until it's dry. The leaf will stay in the shape it is dried in. Experiment with twists and curves, it's so much fun and so perfect for autumn leaves! Repeat for all three leaves.
Spray one of the strips of B&T. Soggy is okay. Gently begin twisting the paper at one end and work your way to the other end being careful not to tear it. Try to get the underside of the paper to show in places as well.
Once the strip of paper is twisted, wrap it around the tool and set it with the heat embossing tool. It takes a little longer than the leaves because of the thickness. When it's set you can pull on the coil and it will bounce back. It it's not bouncing back heat it a little longer. You can take it off the tool to heat once it's got it's basic shape.
View of the lid from the bottom.
View of the lid from the top.
The completed project!

Thanks giving card inside.


Now that I finally have all the new paper packets I've begun creating with them. Hm... creating isn't quite the right word because what I made is entirely by the directions that came with the Workshop On The Go kits. I'm going to share with you anyway because they are so so beautiful!! Instructions for these three cards are in the kit. 